No Salt Catalytic/Magnetic Water Softeners 

What is Catalytic/Magnetic Technology?

Catalytic/Magnetic technology is an alternative method (compared to water softening) for treating hard water without the use of salt/potassium or chemicals. This system requires no maintenance and adds nothing to your water. It prevents hard water scale in your pipes, hot water heater, plumbing fixtures and helps to prevent soap curd and lime scum. This process is achieved by passing water through a spring-loaded chamber, which creates a small pressure drop. This pressure drop initiates the formation of calcium hardness crystals. The calcium hardness crystals then pass through a catalytic surface, which greatly multiplies the number of crystals. It is the last two steps (pressure drop & catalytic surface) that set the patented process apart from similar products. Then the multitude of calcium crystals pass through a strong magnetic field, which serves to hold the crystals in suspension for approximately 24 hours in solution. The final result is that the calcium is rendered harmless to your plumbing fixtures and all the surfaces that come in contact with the water. Household cleaning is reduced to periodically wiping any residual spotting with a damp cloth and perhaps a small amount of vinegar (if needed). Abrasives and "elbow grease" that are normally required to clean spotted surfaces caused by hard water is eliminated. The surface tension of the water is also reduced which results in a superior water absorption into the human cells and plant roots.

Ok, But Does It Really Work?

Yes it does work! The KDF media that is the part of the process that changes the calcium in the water to a form that will pass through the system without allowing it to plate out. Calcium in water comes in two types (1) calcium carbonate which is insoluble in water and will pass right through the water pipes without causing any problems and (2) calcium bi-carbonate which is soluble in water and will plate out on fixtures, water heaters, sinks etc. The catalytic/magnetic part of the water softeners combined with the pressure drop will cause this to crystallize and allow this form of calcium to pass through the water system without permanently changing the calcium form. ( this means that the calcium is still available for up-take in the body, for plants, animals etc.) This media lasts for 10 years.

Why would a different system be needed for 
City water sources vs. Well water systems?

There are many reasons that well water filters are different from city water filters. 
First, city water is regulated and has to meet certain guidelines. Private wells need to be monitored by the owner. Well water also tends to have more sediment and higher mineral contents than City water sources. The Maxi-cure system for Well water systems has a pre-filter which captures these sediments and minerals prior to going through the water softener process. Because of this pre-filter, the Maxi-cure system for well water systems does require backwashing with a minimal amount of water. The Aquafer Water Source for City water systems does not require backwashing at all. No salt is needed for either system and no chemicals are dumped into your waste water system which is a big environmental concern in many places today.

However, knowing that you are on City or Well water systems is not the only factor to consider. We must know something of the chemistry of the water. In particular the Calcium hardness, total alkalinity, and pH. From this we can establish the Langlier's index and apply it to our lab test data. We estimate that 85% of all municipal water supplies can be treated. To obtain this information contact your municipality.

 They test the water on a daily basis and should be able to give you the information over the phone.

If on a private well we would encourage a test of your water.  This test is free to you! Here is all you need to do. Place at least 1 oz of water from your tap into a clean container.  Label the container clearly with your name, address, phone number and email address. Mail to:

We will email you with the results and recommendation within approximately 2 weeks of receipt of your water. Sooner if at all possible. It is as easy at that!

Can I install the unit myself?

If you have any plumbing experience at all you should be able to install the unit yourself. However, we often recommend a plumber for the average home owner.

How is your product different from traditional water softeners?

 

Most water hardness treatment systems rely on sodium ion exchange which can have adverse effects to both people and the environment. While ion exchange systems substitute salt (sodium) for calcium, the Aquafer Water Source and Maxi-Cure System transforms dissolved calcium to crystallized calcium. Calcium in its crystallized state is rendered harmless and free from its objectionable scaling effects.

 

What is your product used for?

The Aquafer Water Source and Maxi-Cure System has several uses. It is primarily used for residential applications where superior water is desired for both taste and functional use. It is also used for commercial applications where scale prevention is required, such as; water heater pre-treatment, reverse osmosis pre-treatment, etc. Examples would be Cash Washes, public Laundromats and industrial applications.

Do regular water softeners waste a lot of water?

It depends on the water hardness, softener design, and the family size. But the average would be about 10,000 gallons a year. That's a lot of water.

It sounds like this unit is very friendly to the environment. Is this true?

Yes it is. Also in many parts of the US there is legislation pending to stop the discharge of the salt into municipal sewers. You can imagine the problems that would be caused by hundreds or thousands of softeners in a single city.

If you have any questions about either one of these systems please feel free to e-mail us at info@healthyhomemall.com.